Allenheath DR128 SERVICE MANUAL Manuel d'utilisateur Page 70
- Page / 114
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
3
DR128 SERVICE MANUAL
INTRODUCTION
The information presented in this section of the manual is intended for competent technical personnel to carry
out service and product support for the
DR
128
. We assume that the reader is familiar with the related electronic
theory and audio terminology, and is able to carry out basic servicing, fault-finding and repair of digital audio
equipment of this type. Service personnel should also be familiar with audio systems, mains earthing and power
requirements, as well as handling precautions.
For information on the installation, operation and application of the
DR
128
please refer to section
A of this manual.
Whilst we believe the information in this manual to be reliable we do not assume responsibility for inaccuracies.
We also reserve the right to make changes in the interest of further product development.
SERVICE AND TECHNICAL SUPPORT
Under normal operating conditions the
DR
128
does not require user maintenance or internal calibration. Any
service work required should be carried out by qualified technical personnel only.
We are able to offer further product support through our worldwide distribution network. To help us provide an
efficient service please quote the unit serial number, the date and place of purchase in any communication
regarding this product
SAFETY WARNING !
Mains electricity is dangerous and can kill. Mains voltage is present within the unit. Except for
Installation and calibration, do not remove any covers with power connected. Do not carry out any
work within the unit while it is powered. High voltage components are insulated for safety but should
not be touched with power applied. The mains voltage setting is indicated on the AC mains input
socket on the rear panel. Check that this matches your local mains supply. Check your mains wiring
and earthing before switching on.
DO NOT REMOVE THE MAINS EARTH CONNECTION!
The chassis is always connected to mains earth. Audio 0V connects to the chassis internally.
Should problems be encountered with ground loops operate the audio ground lift switches on other
equipment connected to the unit or disconnect the cable screens at one end. Refer to the section
on 'EARTHING' in the User Guide.
IMPORTANT STATIC ELECTRICITY
PRECAUTIONS
Many of the components in the
DR
128
are extremely sensitive to static electricity. The following
procedures reduce the possibility of damaging components:
1.) Before handling any components or touching anything inside the unit, discharge
your body's static electric charge by touching a grounded (earthed) surface.
Wear a grounding wrist strap if one is available.
2.) Do not remove parts from their antistatic containers or bags until you are ready
to install them. When removing circuit boards (PCBs) or chips from a unit,
immediately place them in an antistatic bag.
3.) When handling (PCBs), hold them by their edges and avoid touching the circuitry.
4.) Do not slide (PCBs) or ICs over any surface.
5.) Avoid having plastic, vinyl and foam in your work area.
6.) Limiting your movements during service work reduces static electricity.
WARNING: There is danger of explosion if the battery is incorrectly replaced.
Replace the battery with an Allen & Heath recommended part. Using a different battery, recharging or
dissassembling the battery may present a danger due to fire or explosion.
Dispose of used batteries promptly according to the manufacturer's instructions. Keep all batteries away
from childeren
Section B
- ALLEN&HEATH 1
- 12 IN 8 OUT 2
- 24-BIT DIGITAL 2
- MIX PROCESSOR 2
- HOW TO USE THIS MANUAL 3
- SECTION A 4
- Conditions of Warranty 5
- Full Contents 6
- Section 5 - Setup Menu 7
- Section 6 - Appendix 7
- 2 Introduction 9
- Precautions 10
- 4 Introduction 11
- Installation 11
- Introduction 5 12
- Connecting DC Supplies 13
- Introduction 7 14
- 8 Introduction 15
- DR128 Overview 16
- 10 DR128 Overview 17
- Introduction 17
- DR128 Overview 11 18
- Basic Principles 18
- 12 DR128 Overview 19
- DR128 Overview 13 20
- 14 DR128 Overview 21
- Front Panel 21
- DR128 Overview 15 22
- 16 DR128 Overview 23
- Rear Panel 23
- Using the DR128 24
- Using the DR128 19 26
- Function Keys 26
- 20 Using the DR128 27
- Mic 1 Lev 65 27
- PATCH: Patch 02 27
- Using the DR128 21 28
- Mic 1 Lev 45 28
- Mic 1 Lev 55 28
- Patch Select 29
- Patch Recall 30
- Remote Switch Examples 30
- Wiring Remote Switches 30
- 24 Using the DR128 31
- Hardware Configuration 32
- 26 Hardware Configuration 33
- Signal Levels 33
- Hardware Configuration 27 34
- Mic/Line Inputs 34
- 28 Hardware Configuration 35
- Hardware Configuration 29 36
- Line Inputs 36
- 30 Hardware Configuration 37
- Hardware Configuration 31 38
- Balanced Outputs 38
- 32 Hardware Configuration 39
- Setup Menu 40
- Entering Setup Mode 41
- 36 Setup Menu 43
- 0dB -1dB -2dB -3dB -5dB -7dB 47
- 52 Setup Menu 59
- *19 Set Security 59
- SECURITY: ON 59
- Appendix 60
- 54 Appendix 61
- Architect’s Specification 61
- Appendix 55 62
- Technical Specifications 62
- Add/Remove Programs 63
- Appendix 57 64
- 58 Appendix 65
- Appendix 59 66
- 60 Appendix 67
- Reseting the Password 67
- SECTION B 68
- CONTENTS 69
- SAFETY WARNING ! 70
- IMPORTANT STATIC ELECTRICITY 70
- PRECAUTIONS 70
- DR128 SERVICE MANUAL 71
- Service Procedures 71
- Spare parts 75
- Ordering a Spares kit 76
- Spares kit 76
Produits connexes et manuels pour Panneau de contrôle Allenheath DR128 SERVICE MANUAL
(64 pages)Two-brothers-racing Pour la voiture manuels d'utilisation
À partir de Y
Commentaires sur ces manuels